Searching internationl dating sites

6854933580_2c8b688306_z

As I said in the above it will barely move in 1st gear and in Reverse but does nothing in 2nd , 3rd or 4th gear. Re wheel castings with tires an rims or with out please contact me at 309 275-9474 an i work for a farmer his name is Beefy. I need these parts where can i find them or does any one have any of theses parts. Any ideas It was converted to 12 volt and I am going to try a new coil and resistor. The dealer unloaded it and left the operators manual on the kitchen table.

Re wheel castings with tires an rims or with out please contact me at 309 275-9474 an i work for a farmer his name is Beefy. Is there anything else that I should look at The points are making and breaking and there is 12volts at the coil. She says it is a 1934 but I am going to look for the SN. Dad didnt know a thing about it, so I sat down and read the manual for a bit, the went out to try it.

What makes the governor speed lever fly forward I have a 1943 Case VAC tractor that I can t get started since it ran out of gas last summer 2012 I checked the timing , removed the gas tank and cleaned it out, replaced valve under the gas tank,rebuilt the carburetor,installed new plugs,coil,distributor cap,rotor,points, condensor; replaced line from gas tank to carburetor. the brake drum it is on tight it was held in by a snap ring. I love old tractors and specialy M-H 44 744 745 55 JOHN DEER B And CASE 500 And 600 because i was living whith those tractors in ours farm in greece when i was young.-My father bought an Oliver 70 Row Crop in the late 1930 s and we used it until 1948 when we quit farming It had four speeds forward and one reverse.skelton steel wheels on the back and solid steel in front.

What else could be done or replaced to get it to start Looking for a Mc Cormick Deering B-87 two-way moldboard plow for a 1946 B-Farmall or what ever plow was original equipment for a B , or any type one-bottom trip plow that can be pulled by the drawbar of the B tractor. how do you get the drum off to replace the ring gear housing beargings. We also had the Oliver cultivator that were easy to attach and use. During the war years I spent many hours on it.could run against the Allis Chalmers, John Deere s and Farmall s, my only complaint was the steel wheels gave a pretty rough ride at times and limited your use of black top and oil roads. Does anypone know where I might find pictures cira 1937-38 I would like my children to see what life was like in those days I would love to talk to someone that knows alot about a farmall A tractor, I got a 1944 farmall A andit ran as new, but i let it run out of gas and it hasn t hit a lick sence, clean gas glass bowl, clean plugs- has blue/white spark, can choke for 3 or 4 rounds and will wey plugs , check compression - 90 to 108 psi....please somebody tell me what is wroung!

He passed away last spring and I am wondering if we should sell it or keep it for old times sake.

Anyone know what it would be worth It has the sycle on the side and still runs.

searching internationl dating sites-30searching internationl dating sites-23

The governor speed lever just flys forward, but the power isn t there. a 44 massey harris tractor need to know how to pull the brake hub apart. On 1955 my father and my ungle left 44k and buy one M-H 745 But make in England.

It had the high steering wheel with the trottle to the right of the steering wheel.. I loved that tractor, it did a good job on a 4 row front mount #461 cultivator, or a 4 14s 370 plow. We had a M5 Moline gas that was a slug compared to my Farmall. I have used Hercules to plow the snow from my 600 foot driveway for the last ten years with no problems except he doesn t like to start when it s double digits below zero, censius .

I could outwork the Moline and use less fuel, and had that distinct crack of the diesel to listen to. The governer would kick in and the stack poured out thick black smoke. Yesterday he tried to start on the first turn over but sputtered to a stop.

We don t know much about tractors, but am confused how Farmall and International Harvester is one and the same Any idea how we can find out its value Thank you in advance. If anyone has knowledge of this I would offer 500 and a good bbq sandwich. I am meccanical ingenier and i am workin till now as director for a big mattalurgical company.

I have a 1974 Farmall cub with plow, cultivator, disc, back blade and bushhog. The splines on the pto drive shaft are worn and this needs to be replaced. I have a Farmall A that has always been a workhorse. Th boy will regret he was ever a part of my family. I just purchased a 47 44-6 massey and a 101 senior both have a six cylinder contineals. But i love tractors because i cam by agricultur fammily.

Then dad comes along and cranks it and let it run until the valves froze in it. Did it harm the piston and rings or can I just take off the head and regrind the valves.

You must have an account to comment. Please register or login here!